Barnaby Walters

Arranging atoms and pressurising air in a variety of manners.

✨🌟 shiny inevitable mortality distractions! 🛠 building a cultural heritage centre at Wassermühle Brömsenberg 💃🏻 playing old music for new dancing with Duo Gerhardt & Walters 🎼 building hurdy gurdies, playing gurdy blockflute dulcimer accordion Pd voice 🚀 building the indieweb ❤️ philosophising inexpertly about how humans communicate, relate and connect ⚖ helping assess the Icelandic school system at Skólapúlsinn 🍕 baking pizza, granola, bread 🌟✨

Pronouns: he/him/his

  1. about tcpdump, a very handy little command line utility for looking at network traffic. Not as fully featured as Wireshark, but nice if you want to e.g. pipe network traffic into another process. It’s also not >300MB :/

  2. When using the python2.7 gzip module with StringIO, it’s extremely important to call GzipFile.close() after you’ve finished writing to it. If you don’t, the archive will probably not be readable as the CRC record will not be appended, and you’ll get a bunch of IOErrors despite everything looking fine.

  3. I tried to plug in this LED strip I bought but nothing happens. 5400 LEDs but none of them turn on?! and when I tried to peel the backing off to stick it to something, all the LEDs fell out D: 0/10 would not buy again

    Picture shows a reel containing surface mount LEDs, ready to be fed into a pick and place machine.

  4. For anyone building theSlowGrowth’s Monome Arc clone project, here are the avrdude commands required to set the ATMega88p fuses, based on this fuse calculation:

    avrdude -V -p m88p -c YOUR_PROGRAMMER_ID -P YOUR_PROGRAMMER_PORT -B 10 -e -u -U lfuse:w:0xD6:m -U hfuse:w:0xDF:m -U efuse:w:0xF9:m -U lock:w:0xFF:m

    and then flashing the precompiled firmware is pretty straightfoward. USB board: (swap arc4_ for arc2_ in the unlikely event you’re building an arc2):

    avrdude -V -p m88p -c YOUR_PROGRAMMER_ID -P YOUR_PROGRAMMER_PORT -B 2 -U flash:w:./firmware/compiled_hex/arc4_firmware_usb_board_atmega88p.hex:i -U lock:w:0xFF:m

    and for each ring:

    avrdude -V -p m88p -c YOUR_PROGRAMMER_ID -P YOUR_PROGRAMMER_PORT -B 2 -U flash:w:./firmware/compiled_hex/firmware_pot_board_atmega88p.hex:i -U lock:w:0xFF:m

    Note that the verion of avrdude I’m using (5.8, from an old crosspack install I was using to compile some MI AVR code) doesn’t support the ATMega88p, and in order for any of this to work, you may need to edit the avrdude config file according to the instructions in the arc clone repo. Mine was in /usr/local/CrossPack-AVR-20100115/etc/avrdude.conf, and all I had to do was duplicate the config block for the ATMega88 and make the following changes:

    id               = "m88p";
    desc             = "ATMEGA88P";


    signature        = 0x1e 0x93 0x0f;
  5. Sacred Harp is some of the most exciting music I’ve come across in years, but, being polyphony, you need a group of people to properly enjoy it. Sometimes, once a week really isn’t enough, and an evening in front of a multitrack recorder has to suffice…

    EDIT: I couldn’t resist also recording this parody version. 50% of Sacred Harp is a bunch of biblical and religious stuff but most of the rest, including 209, is pure, unadultered memento mori.

  6. Found this nice ISMLP category page while starting research for a new project, containing enough baroque French gurdy scores to keep anyone busy for a while

    There’s all sorts of interesting stuff if you poke around a bit — for example, in Bordet’s Méthode raisonnée pour apprendre la musique there’s a summary of the hurdy gurdy which suggests that extended keyboards beyond the usual two-octaves-minus-high-F# existed, but were “extraordinaire, et peu usité:”